Circulation pump ESN40-20-1.5 (1500W)
Article: ESN40-20-1.5
| Mains voltage | 380 V |
| Rotation speed | 2900 rot/min |
| Power | 1500 W |
| Maximum water temperature | 104 °C |
| Pressure | 20 m |
| The diameter of the connection connector | 40 mm |
| The diameter of the outlet | 40 mm |
| Class | 155(F) |
| Degree of protection | IP55 |
| Throughput capacity | 12.5 m³/hour |
| Warranty | 12 months |
Circulation pump EPA ESN40-20-1.5 (1500 W)
This pump is designed to keep liquid moving continuously at industrial sites and in heating and water circulation systems. Its 1500 W three-phase motor runs at 2900 rpm, delivering a flow of 12.5 m³/h and a head of up to 20 m. The wetted parts are made of cast iron and withstand pressure and wear, while the motor housing is aluminium, which lets a heated pump cool down quickly. Its ability to handle hot water up to 104 °C allows installation directly in boiler rooms and heating circuits.
Advantages
- Three-phase 380 V motor — delivers stable, powerful operation in industrial conditions
- High flow of 12.5 m³/h and 20 m head — circulates large-volume systems and long circuits in full
- Aluminium upper housing, rear cover and bearing housing — dissipate heat quickly and keep the pump from overheating
- Full copper winding — improves motor durability and extends service life
- Bearing assemblies at both ends — keep the shaft running true and centred, reducing vibration
- Cast iron mid housing, wetted parts and impeller — withstand high pressure and prolonged wear
- Heat-resistant shaft seal — maintains a tight seal when running hot water
- IP55 protection rating and 155(F) insulation class — protection against dust, splashing water and overheating
- Matching 40 mm inlet and outlet — connects straight to the pipeline without adapters
Application
Used to circulate hot water through heating circuits and to keep water moving in hot water supply networks. Widely used in industrial zones, boiler rooms, multi-storey residential buildings, offices and production facilities, in both heating and cooling systems.
Note on use
The pump is always connected to the 380 V supply through a circuit breaker and a magnetic starter. Without protective gear, the loss of one phase or any other fault will burn out the motor. Properly installed protection significantly extends the pump's service life.
EPA ESN40-20-1.5 — a powerful, reliable pump for heating and water circulation systems.
Circulation pump EPA ESN40-20-1.5 (1500 W)
This pump is designed to keep liquid moving continuously at industrial sites and in heating and water circulation systems. Its 1500 W three-phase motor runs at 2900 rpm, delivering a flow of 12.5 m³/h and a head of up to 20 m. The wetted parts are made of cast iron and withstand pressure and wear, while the motor housing is aluminium, which lets a heated pump cool down quickly. Its ability to handle hot water up to 104 °C allows installation directly in boiler rooms and heating circuits.
Advantages
- Three-phase 380 V motor — delivers stable, powerful operation in industrial conditions
- High flow of 12.5 m³/h and 20 m head — circulates large-volume systems and long circuits in full
- Aluminium upper housing, rear cover and bearing housing — dissipate heat quickly and keep the pump from overheating
- Full copper winding — improves motor durability and extends service life
- Bearing assemblies at both ends — keep the shaft running true and centred, reducing vibration
- Cast iron mid housing, wetted parts and impeller — withstand high pressure and prolonged wear
- Heat-resistant shaft seal — maintains a tight seal when running hot water
- IP55 protection rating and 155(F) insulation class — protection against dust, splashing water and overheating
- Matching 40 mm inlet and outlet — connects straight to the pipeline without adapters
Application
Used to circulate hot water through heating circuits and to keep water moving in hot water supply networks. Widely used in industrial zones, boiler rooms, multi-storey residential buildings, offices and production facilities, in both heating and cooling systems.
Note on use
The pump is always connected to the 380 V supply through a circuit breaker and a magnetic starter. Without protective gear, the loss of one phase or any other fault will burn out the motor. Properly installed protection significantly extends the pump's service life.
EPA ESN40-20-1.5 — a powerful, reliable pump for heating and water circulation systems.














